- Startseite
- Alle Kategorien anzeigen
- Modelle und Clones
- A1000 Turbokarten
- A1200 Turbokarten
- A2000 Turbokarten
- A3000 Turbokarten
- A4000 Turbokarten
- A500 Turbokarten
- A600 Turbokarten
- Bridgeboards & Emulatorkarten
- CD32 Turbokarten
- CDTV Turbokarten
- Custom Chips
- Digitiser & Framegrabber
- Flickerfixer & Scandoubler
- Floppy Controller
- Genlocks
- Grafik (non RTG) & Videokarten
- Grafikkarten (RTG)
- I/O Karten
- IDE Controller
- ISDN & Modem
- Tastaturen & Adapter
- Kickstart Umschalter
- MIDI Geraete
- versch. ZORRO Karten
- verschiedene Hardware
- Monitore
- Netzwerk Karten
- Prozessoren
- RAM Erweiterungen
- Scanner
- SCSI Controller
- Sound Karten
- Soundsampler
- Bandlaufwerke & Backup
- Time Base Correctors
- Tower Kits
- Zorro Erweiterungen & Busboards
- Mystery Corner
- Suche über Anschluss
- Sitemap
A2000 Turbokarten
Phase 5: Blizzard Turbo
Connection: CPU Socket |
This card has 5 memory banks known as Shadow, Bank 0, Bank1, Bank2 and Bank3.
High Res Version - 103K
Processor: | 68000@14Mhz |
FPU: | None |
MMU: | None |
Max Ram: | 8MB |
Ram Type: | DRAM Chips |
Plugs into the CPU socket of the A2000 or A500. The board takes either 256K*4 DRAMs 100ns or faster (eg SIEMENS HYB514256B) for a maximum of 2MB or 1MB*4 DRAMs preferably faster than 100ns (eg TOSHIBA TC514400P) for a maximum of 8MB of RAM. It possible to mix and match the two types, however it may not always work so some experimentation may be needed.
Mem Size | BANK 0 | BANK 1 | BANK 2 | BANK 3 | DIP 3-6 1 = ON, 0 = OFF (Ascending Order) |
1 MB | 4x256K*4 | 4x256K*4 | - | - | 0-1-1-1 |
2 MB | 4x256K*4 4x1M*4 | 4x256K*4 | 4x256K*4 | 4x256K*4 | 0-1-0-1 1-0-1-1 |
3 MB | 4x256K*4 | 4x256K*4 | 4x1M*4 | - | 0-1-1-0 |
4 MB | 4x1M*4 | 4x1M*4 | - | - | 0-0-1-1 |
5 MB | 4x256K*4 | 4x256K*4 | 4x1M*4 | 4x1M*4 | 0-1-0-0 |
6 MB | 4x1M*4 | - | 4x1M*4 | 4x1M*4 | 1-0-0-0 |
8 MB | 4x1M*4 | 4x1M*4 | 4x1M*4 | 4x1M*$ | 0-0-0-0 |
Note: For any empty memory banks, all DIP switches should be set to ON. A memory testing program was usually supplied with this board to test for defective memory, in order to use it DIP switch 2 must be set to on.Jumpers J1 and J2 are set at the factory and must not be changed. Pin1 of the jumpers are not clearly identifed, however both jumpers should have the two pins shorted that are farthest away from the J1/J2 labels. DIP Switch 1 is used to set the startup frequency of the card between 7Mhz and 14Mhz, you will have to experiment to find which setting of the DIP switch matches which frequency. All user settings are accomplished using the 6 dip switches. Shadow RAM can be used to softkick another another kickstart, including 3.1.
Contributions to this page by:
Andreas C Schmidt, Erasmus Kuhlmann, Rainer Kraus, Ron Mascaro
Letzte Änderung des Artikels: 2009-01-25 10:39
Revision: 1.0
Kommentieren nicht möglich