- Startseite
- Alle Kategorien anzeigen
- Modelle und Clones
- A1000 Turbokarten
- A1200 Turbokarten
- A2000 Turbokarten
- A3000 Turbokarten
- A4000 Turbokarten
- A500 Turbokarten
- A600 Turbokarten
- Bridgeboards & Emulatorkarten
- CD32 Turbokarten
- CDTV Turbokarten
- Custom Chips
- Digitiser & Framegrabber
- Flickerfixer & Scandoubler
- Floppy Controller
- Genlocks
- Grafik (non RTG) & Videokarten
- Grafikkarten (RTG)
- I/O Karten
- IDE Controller
- ISDN & Modem
- Tastaturen & Adapter
- Kickstart Umschalter
- MIDI Geraete
- versch. ZORRO Karten
- verschiedene Hardware
- Monitore
- Netzwerk Karten
- Prozessoren
- RAM Erweiterungen
- Scanner
- SCSI Controller
- Sound Karten
- Soundsampler
- Bandlaufwerke & Backup
- Time Base Correctors
- Tower Kits
- Zorro Erweiterungen & Busboards
- Mystery Corner
- Suche über Anschluss
- Sitemap
Netzwerk Karten
Hydra Systems: AmigaNet Zorro II
Connection: Zorro II |
Rev 1.1 card with 2 x BNC and 1 x AUI
Rev 1.1 card with 2 x BNC and 1 x AUI
Rev 1.1 card with 1 x BNC and 1 x AUI
Rev 1.1A card with 1 x BNC and 1 x AUI, Front
Rev 1.2 card with 1 x BNC
Rev 1.1A card with 1 x BNC and 1 x AUI, Back
Hi Res Version, Rev 1.0 - 417K
Hi Res Version, Rev 1.1, 2 x BNC, 1 x AUI - 59K
Hi Res Version, Rev 1.1, 1 x BNC, 1 x AUI - 829K
Hi Res Version, Rev 1.1A, Front - 448K
Hi Res Version, Rev 1.2 - 353K
Hi Res Version, Rev 1.1A, Back - 378K
Closeup of Rev 1.1A card, left side - 579K
Closeup of Rev 1.1A card, right side - 573K
Type: | Ethernet |
10Base2 (BNC & Coax, ThinNet): | Yes |
10Base5 (AUI & Coax, ThickNet): | Yes (Rev V1.1 and earlier boards) |
10BaseT (RJ45 & UTP): | Yes (no for Rev V1.1 boards and earlier, some cards may require the connector upgrade) |
100BaseTX (RJ45 & UTP): | No |
SANA-II Driver: | Yes (hydra.device) |
MNI Driver: | Yes (z2-dp8390.mni) |
Other Driver: | No |
The AmigaNet is a full length Zorro II Ethernet card (NatSemi 32490CN) for the Amiga. Depending on the specific versions of the card, it supports 10Base5, 10Base2 and 10BaseT. To support 10BaseT, your card may require an optional upgrade to attach the RJ45 connector to the board. Earlier revisions of the board have two BNC connectors, rather than the conventional single connector that most ethernet cards have. This means you do not need the "T" connector which you do with other ethernet cards. You simply attach both BNC connectors to the same network segment. The AmigaNet has been reported to transfer at up to 600k/sec. The Zorro II network card released by GVP called the A-Net 2000 was simply this card rebadged.
Jumpers
There is only one set of jumpers, block F1, which has six pairs of pins. When all are in the down position, it is set to ThinNet 10Base2 (CheaperNet). When all are jumpered in the up position, it is set to use the AUI port for 10Base5.
Board Layout
_________________________________________________________________
| |___
| |
| :::::: F1 |
| |# 10Base5
| |# /AUI
| |# Port
| |# (DB15)
| |#
| |_
| |_| BNC
| |_
| |_| BNC
|_________________________________________________________________|
||||||||||||||||||||||||||| |
Contributions to this page by:
Calum Tsang, Mats Magnusson, RiWa & Friends, Takahasi Kasiko, Thomas Weygand, Warren Block
Letzte Änderung des Artikels: 2009-01-26 21:28
Revision: 1.0
Kommentieren nicht möglich